Why install fluorescent fiber optic temperature measurement devices on transformer windings-INNO

Installing a fluorescence fiber-optic temperature monitoring system on transformer windings aims at accurato, sicuro, real-time hotspot temperature monitoring, which is crucial for ensuring reliable operation, extending service life, and preventing faults. The necessity is analyzed below from three perspectives: transformer operational needs, limitations of traditional temperature measurements, and the advantages of fluorescence fiber-optic technology.

IO. Core need: winding temperature is the “lifeline of safe operation”

A transformer is a key device in power systems. Its windings (copper/aluminum conductors) continuously heat up under load due to copper loss (Riscaldamento I²R) E core loss (hysteresis/eddy currents). Winding temperature directly determines the transformer’s operating state:

Misurazione della temperatura in fibra ottica del trasformatore-1

Limits loading capability: According to international standards, when the winding hotspot temperature of an oil-immersed transformer exceeds its rated value, service life shortens rapidly. Per trasformatori a secco, excessive winding temperature accelerates insulation aging. Perciò, winding temperature is the core basis to decide whether the unit can run at “full load” or under “overload.”
Prevents sudden failures: Local overheating in windings (per esempio., turn-to-turn fault, poor conductor contact) can quickly damage insulation. If not detected in time, it may lead to winding burn-out, transformer explosion, or even grid outages.
Optimizes O&M strategy: Real-time winding temperature monitoring prevents both “over-maintenance” (per esempio., unnecessary shutdowns) and “under-maintenance” (per esempio., ignored overheating risks), consentendo la manutenzione basata sulle condizioni.

II. Limits of traditional methods: cannot meet the need for “precise monitoring of the winding itself”

Before fluorescence fiber-optic sensing, common approaches (per esempio., oil temperature thermocouples, DC resistance-based estimation) had clear shortcomings and could not reflect true winding hotspots:

Metodo	Measured object	Core drawbacks
Top-oil temperature	Olio per trasformatori (indiretto)	1) Oil is a heat transfer medium; oil temperature is lower than winding hotspots and cannot reflect true winding temperature; 2) Only overall oil temperature is seen; local overheating (per esempio., a specific turn fault) cannot be located.
DC resistance method	Winding resistance (indiretto)	1) Offline: Requires outage, cannot monitor temperature in real time; 2) Reflects only average temperature, missing “hotspots.”
Termografia a infrarossi	Superficie di avvolgimento (esterno)	1) Mainly for dry-type units and often requires opening enclosures; it cannot monitor internal windings of oil-immersed transformers; 2) Affected by dust and insulation遮挡, leading to larger errors.

Insomma, traditional methods are either “indirect estimation” or “offline and lagging,” and cannot meet the demand for in tempo reale, diretto, e accurato monitoring of winding temperature — the core reason to adopt fluorescence fiber-optic systems.

III. Advantages of fluorescence fiber-optic systems: perfectly matched to winding temperature monitoring

Fluorescence fiber-optic sensing is based on the “fluorescence lifetime principle.” Sensors are embedded directly in the winding’s “hotspot regions” (often mid-to-upper sections where heat concentrates). Quando eccitato dalla luce, the sensor emits fluorescence whose lifetime shortens as temperature rises. By detecting lifetime changes, the system computes real-time temperature. Its advantages fit the winding scenario:

1) Accurate measurement: directly captures winding “hotspot temperature”

Sensors can be embedded between conductors, avoiding indirect heat transfer through oil or other media. This reflects the winding’s true maximum temperature (punto caldo), solving the lag of oil-based estimation.
Supports multi-point monitoring (per esempio., several sensors on HV and LV windings), enabling localization of local overheating and providing precise data for diagnostics.

2) Sicuro e affidabile: suitable for high voltage and strong EMI environments

Isolamento elettrico: Silica-based optical fibers are non-conductive and free from electromagnetic induction. They can be placed close to high-voltage windings without introducing leakage or short-circuit risks, avoiding interference with the insulation system.
Immunità EMI: Transformers produce strong electromagnetic fields (per esempio., leakage flux, short-circuit forces). Traditional electrical sensors (termocoppie, RTD) are susceptible to interference, causing distortion. Le fibre ottiche trasportano la luce, immune alle EMI, and remain stable under short-circuit and lightning events.

3) Stabilità a lungo termine: withstands harsh internal environments

Inside transformers there are heat, olio, e vibrazioni. Fluorescence fiber sensors offer high temperature tolerance, chemical resistance to transformer oil, and strong mechanical robustness to winding processes and vibration, aligning with transformer O&M cycles.

4) Real-time response: gains time for early warning

With rapid sampling, sudden temperature rises from issues like turn-to-turn faults can be detected in seconds, innescando allarmi (per esempio., audible-visual alerts, messages) so operators can derate or schedule maintenance in time to avoid escalation.

Riepilogo

Installing fluorescence fiber-optic temperature systems fundamentally solves the core pain points of winding temperature monitoring — “hard to measure, inaccurate, unsafe.” Through direct, accurato, monitoraggio in tempo reale, it provides a sound basis for “full-load operation,” enables early warning of local overheating, ensures grid stability, and reduces economic loss and outage risk. This approach has become a standard monitoring option for high-voltage and large industrial transformers.