Why install fluorescent fiber optic temperature measurement devices on transformer windings-INNO

Installing a fluorescence fiber-optic temperature monitoring system on transformer windings aims at دقيق, آمن, real-time hotspot temperature monitoring, which is crucial for ensuring reliable operation, extending service life, and preventing faults. The necessity is analyzed below from three perspectives: transformer operational needs, limitations of traditional temperature measurements, and the advantages of fluorescence fiber-optic technology.

أنا. Core need: winding temperature is the “lifeline of safe operation”

A transformer is a key device in power systems. Its windings (copper/aluminum conductors) continuously heat up under load due to فقدان النحاس (تسخين I²R) و الخسارة الأساسية (hysteresis/eddy currents). Winding temperature directly determines the transformer’s operating state:

قياس درجة حرارة الألياف الضوئية للمحولات -1

Limits loading capability: According to international standards, when the winding hotspot temperature of an oil-immersed transformer exceeds its rated value, service life shortens rapidly. للمحولات من النوع الجاف, excessive winding temperature accelerates insulation aging. لذلك, winding temperature is the core basis to decide whether the unit can run at “full load” or under “overload.”
Prevents sudden failures: Local overheating in windings (على سبيل المثال, turn-to-turn fault, poor conductor contact) can quickly damage insulation. If not detected in time, it may lead to winding burn-out, transformer explosion, or even grid outages.
Optimizes O&M strategy: Real-time winding temperature monitoring prevents both “over-maintenance” (على سبيل المثال, unnecessary shutdowns) and “under-maintenance” (على سبيل المثال, ignored overheating risks), enabling condition-based maintenance.

II. Limits of traditional methods: cannot meet the need for “precise monitoring of the winding itself”

Before fluorescence fiber-optic sensing, common approaches (على سبيل المثال, oil temperature thermocouples, DC resistance-based estimation) had clear shortcomings and could not reflect true winding hotspots:

طريقة	Measured object	Core drawbacks
Top-oil temperature	زيت المحولات (غير مباشر)	1) Oil is a heat transfer medium; oil temperature is lower than winding hotspots and cannot reflect true winding temperature; 2) Only overall oil temperature is seen; local overheating (على سبيل المثال, a specific turn fault) cannot be located.
DC resistance method	مقاومة اللف (غير مباشر)	1) غير متصل: Requires outage, cannot monitor temperature in real time; 2) Reflects only average temperature, missing “hotspots.”
التصوير الحراري بالأشعة تحت الحمراء	Winding surface (external)	1) Mainly for dry-type units and often requires opening enclosures; it cannot monitor internal windings of oil-immersed transformers; 2) Affected by dust and insulation遮挡, leading to larger errors.

باختصار, traditional methods are either “indirect estimation” or “offline and lagging,” and cannot meet the demand for في الوقت الحالى, مباشر, ودقيقة monitoring of winding temperature — the core reason to adopt fluorescence fiber-optic systems.

III. Advantages of fluorescence fiber-optic systems: perfectly matched to winding temperature monitoring

Fluorescence fiber-optic sensing is based on the “fluorescence lifetime principle.” Sensors are embedded directly in the winding’s “hotspot regions” (often mid-to-upper sections where heat concentrates). عندما يثار بالضوء, the sensor emits fluorescence whose lifetime shortens as temperature rises. By detecting lifetime changes, the system computes real-time temperature. Its advantages fit the winding scenario:

1) Accurate measurement: directly captures winding “hotspot temperature”

Sensors can be embedded between conductors, avoiding indirect heat transfer through oil or other media. This reflects the winding’s true maximum temperature (نقطة اتصال), solving the lag of oil-based estimation.
Supports multi-point monitoring (على سبيل المثال, several sensors on HV and LV windings), enabling localization of local overheating and providing precise data for diagnostics.

2) آمنة وموثوقة: suitable for high voltage and strong EMI environments

العزل الكهربائي: Silica-based optical fibers are non-conductive and free from electromagnetic induction. They can be placed close to high-voltage windings without introducing leakage or short-circuit risks, avoiding interference with the insulation system.
مناعة EMI: Transformers produce strong electromagnetic fields (على سبيل المثال, leakage flux, قوى الدائرة القصيرة). Traditional electrical sensors (المزدوجات الحرارية, أهداف التنمية المستدامة) عرضة للتدخل, causing distortion. الألياف الضوئية تحمل الضوء, محصن ضد EMI, and remain stable under short-circuit and lightning events.

3) الاستقرار على المدى الطويل: withstands harsh internal environments

Inside transformers there are heat, زيت, والاهتزاز. Fluorescence fiber sensors offer high temperature tolerance, chemical resistance to transformer oil, and strong mechanical robustness to winding processes and vibration, aligning with transformer O&M cycles.

4) الاستجابة في الوقت الحقيقي: gains time for early warning

With rapid sampling, sudden temperature rises from issues like turn-to-turn faults can be detected in seconds, إطلاق الإنذارات (على سبيل المثال, audible-visual alerts, messages) so operators can derate or schedule maintenance in time to avoid escalation.

Summary

Installing fluorescence fiber-optic temperature systems fundamentally solves the core pain points of winding temperature monitoring — “hard to measure, inaccurate, unsafe.” Through direct, دقيق, مراقبة في الوقت الحقيقي, it provides a sound basis for “full-load operation,” enables early warning of local overheating, ensures grid stability, and reduces economic loss and outage risk. This approach has become a standard monitoring option for high-voltage and large industrial transformers.